What is the last step in the 8 step process for establishing and verifying an electrically safe work condition?

How do you verify an electrically safe work condition?

Procedure to Establish an Electrically Safe Work Condition

  1. Identify and locate all possible sources of electric supply. …
  2. Properly interrupt the load current(s) and open the disconnecting device(s). …
  3. Verify deenergization through visual inspection of the disconnect contacts. …
  4. Release stored electrical energy.

What is the 1st step in the 8 step process for establishing and verifying an electrically safe work condition?

The first step in the eight-step process of verification of an ESWC is to determine all possible sources of electrical supply to the equipment. This would include backup or alternates sources of supply and sources from equipment that has not been commissioned but is connected to a source of voltage.

THIS IS INTERESTING:  What is the orientation of electric dipole for more torque?

How many steps are included in the process to create an electrically safe work condition?

Article 120.1 of NFPA 70E outlines six steps that must be followed to insure that employees are working in an electrically safe work condition.

When should an electrically safe work condition be established?

Section 130.2 of NFPA 70E requires that energized electrical conductors and circuit parts that are operating at or over 50 volts be put into an electrically safe working condition if: (1) the employee is working within the limited approach boundary, or, (2) the employee is interacting with equipment where circuit …

Which step should you take to ensure the safe use of electrical equipment in your work environment?

10 Electrical Safety Tips for the Workplace

  1. Prevent All Potential Contact With Live Electrical Current. …
  2. De-energize Equipment and Use Lockout/Tagout. …
  3. Ensure Safe Use of Electrical Equipment. …
  4. Install Proper Physical Barriers Around Electrical Hazards. …
  5. Beware of Conductive Tools and Cleaning Materials.

Which step should you take to ensure the safe use of electrical equipment?

Preventative Steps and Safe Work

  1. Inspect wiring of equipment before each use. …
  2. Use safe work practices every time electrical equipment is used.
  3. Know the location and how to operate shut-off switches and/or circuit breaker panels. …
  4. Limit the use of extension cords. …
  5. Multi-plug adapters must have circuit breakers or fuses.

What is Category 2 arc flash?

In PPE CAT 2, workers need the following clothing: Required Clothing: Arc Rated Long Sleeve Shirt and Pants or Arc Rated Coverall with minimum arc rating of 8 cal/cm. 2. Required AR Face and Head Protection: Arc Rated Arc Flash Suit Hood or AR Face Shield, Sock Hood/Balaclava with minimum arc rating of 8 cal/cm. 2.

THIS IS INTERESTING:  Which energy is the ultimate source of energy?

Which of the following is the first step in a shock hazard analysis?

Step 1 – Perform a Shock Hazard Risk Assessment

Start the assessment by breaking down the type of work employees are doing and what, if any, electrical hazards they are exposed to.

What is mainly covered in Chapter 2 of the NFPA 70E standard?

(1) Chapter 2 covers practical safety-related maintenance requirements for electrical equipment and installations in workplaces as included in 90.2. These requirements identify only that maintenance directly associated with employee safety.

What is the Six Step safety method?

Six Steps to Control Workplace Hazards

  1. Step 1: Design or re-organise to eliminate hazards. …
  2. Step 2: Substitute the hazard with something safer. …
  3. Step 3: Isolate the hazard from people. …
  4. Step 4: Use engineering controls. …
  5. Step 5: Use administrative controls. …
  6. Step 6: Use Personal Protective Equipment (PPE)

What is the first step in creating an electrically safe working condition?

Six-Step Procedure for Establishing an Electrically Safe Work Condition

  1. Identify power source. …
  2. Disconnect power sources. …
  3. Verify that power is off. …
  4. Lockout/tagout. …
  5. Verify again. …
  6. Discharge stored electrical energy (and install safety grounds under certain conditions)

What are the three steps to follow to confirm circuit is de energized before starting work?

Test the circuit – Verify that the equipment or system has been de-energized.

Follow These Steps to Ensure Circuit Safety

  • De-energize the circuit.
  • Lock out.
  • Tag out.
  • Test the circuit.
  • Verify the testing device.